Type 1 Complex
rf90951a Type 1 Refdisk
rd9095a Diagnostics (common to all T1-4)
Specifications
        Memory supported, cache, features
        256K Cache Daughtercard for Type 1
           L2 Cache Performance
        ODP vs. ODPR
        Support for >1GB Disks as IML Drive
"G" 486SX 20 MHz
       "G" Processor Upgrade
"J" 486DX 25 MHz 64F0201
"K" 486DX 33 MHz 64F0198
     What is the Square Of Death?
       Square of Death Limits
     ECA 0530 OKx complexes with P/N 
Upgrade 486DX2 66/33  92F0145
        Supports Non-IML!
Upgrade 486DX 50 MHz  92F0048


"G" 486SX 20 MHz
J2 SX / DX
OS1
20.0000 MHz Osc
U1 CPU
U7 57F2194 Memory Controller
U16, 20 78F1659 Memory Data Buffer
U30 78F1659 MCA Buffer
U36 BIOS (AM27C010)
U38 90X8134 DMA Controller0

   On the 20-MHz board, the jumper 2 must be in positions 1 and 2 if a 487SX processor is installed in connector 3 . If there isn't a 487SX in connector 3 , the jumper must be in positions 2 and 3.



Optional Processors for "G" Complexes


© Copyright IBM Corp.

 20 and 25 Mhz Processor Boards
   For SX models, you can install an optional processor on a 20 or 25 MHz processor board. 
  The 25-MHz processor board (above right) has a second processor connector 3 for either an optional 487SX processor or an 80486SX 25/50 MHz processor. If you install an option processor in connector 3 , of the 25 MHz board, you do not have to remove the existing processor (it is overridden). 
   Carefully insert the tip of a screwdriver between the processor and the connector edge and gently twist the screwdriver (around all edges) until the processor raises up. 

NOTE: When you reinstall the processor, align the beveled corner 1 with the beveled corner marked on the board. 


256K 17nS Cache Daughtercard

Side Toward Complex
J1 159 Pin Header  AMP 650754-1
TD1  Fil-Mag 77Z14A030
TD2, TD4 Fil-Mag 77Z14A025
TD5, TD6 Fil-Mag 77Z14A045
U18-U21 SDT 74FCT646ASO
U22, U23 TIT031XS AS573A
U24-U27 Toshiba TC55329J-17

Side Away From Complex
U1-U4  Toshiba TC55329J-17
U5, U6, U8 TI SN74ACT 2160-17FM
U10 AMD 64F6043
U11 AMD 84F8257
U12 AMD 64F6065
U13 AMD 84F8261
U14 AMD 64F6046
U15 AMD 64F6048
U16 AMD 84F7970
U17 AMD 64F6066
Ed. The chips change from module to module. Yours may be different.

256 KB Cache Memory Option Kit, 6451095 (64F0199 same thing)

L2 Cache Performance
From Us, the god-Emperor of Microchannel
   Praytell, what use can one make of the 256K cache for the T1 complexes? I hate to admit it, but I never noticed a large (or significant) boost when I added one. 

From Tony Ingenoso
   The effects of modern bloatware on a write-through can be disheartening... IMO IBM's matched cycle scheme goes a long way towards helping keep the L1 lines filled at a brisk pace even when no L2 is present.  The T2's abnormally good performance (considering its other genetic limitations) shows this well.  For all practical purposes, 90/95's have a 64 bit memory subsystem working to fill the L1 lines.

From Charles Lasitter
   What do you see with one speed processors (DX50) that are coupled with a faster cache 64F0050, or the T3 and integrated cache? Since they don't have a 'fall back' processing speed in the event of an L1 miss, but rather use a 12ns L2 vs 17ns, is there any difference for them?
   I believe we've seen LARGE increases in speed when doing something like kernel rebuilds compared to no cache.  I think it may depend on what you're doing and the operating system.

From Tony
   I don't see this as a core multiplier issue -- even the low end DX25 T2 runs better than one might expect it to. The kernel rebuild improvements aren't suprising - compilation algorithms and the bits of data they work tend to be well localized if modules aren't too massive.  Initial parsing would be very read intensive as well and should make good use of an L2. Cache perf is indeed a very task specific kind of thing.  Scattered code/data can effectively neutralize it totally.
   DX50's are strange -- they often outrun DX2-66 when main memory bandwidth or I/O is the constraint.  When staying in L1, then the DX2-66 wins due to the multiplier.   With a fast L2 and fairly scattered code/data a DX50 is going to do very well.

From Peter
   Uhmmm ... I had the occasion to test a T1 DX2-33/66 board under Linux. And compare it with the same T1 DX-50 (!) board - both with the L2 cache. 
   The 486DX2-33/66 showed 33 BogoMips, the DX50 25 only ... same as the T3 DX50 while a DX2-50/100 (Intel DX4-100 in 2x mode) on a T3-platform runs at -supposed- 50 Bogomips almost.
   In the practical use the T1 DX50 wasn't much slower than the T1 DX2 - the XF86 stuff paced at the same rate on both. None of the machines "felt" faster or slower. The DX4 T3 was a bit faster - but not significantly. All 3 machines had the same XGA-2 card, the same TR 16/4 network adapter, the same 32MB Parity RAM and the same IBM 400MB HD with the Linux on it.
   The T1 platforms had the "plug on" 256K L2 cache (17ns on the DX2, 12ns on the DX50) and the T3 had its own integrated cache. I did not write down all the values ... maybe I should repeat that session again to get some definite, comparable data.



ODP vs. ODPR
   The 169 pin is the ODP-version - substitutes a 487SX with the 486SX still in place. Important on boards with soldered CPU.
   The 168 pin is the ODPR-version, where the -R- stands for "Replace" ... it replaces the 486SX / 486DX respectively and does not need the "SX-disable" pin therefore.

SCSI drives >1GB as IML
Type 1 complexes (with the exception of the DX2-66 Upgrade, 92F0145) need a BIOS 52G9509 to handle IML drives of >1,023MB. (EPROM in drawing)
  The upgrade provides the following additional capabilities:
  1. Adapter ROM memory more efficiently utilized to minimize adapter configuration conflicts.
  2. BIOS support for fixed disks up to 3.94 gigabytes per device.
  3. Supports "Search IML" from any PUN (Physical Unit Number) or SCSI ID.  The system partition is no longer restricted to only SCSI ID=3D6.  Each fixed disk ID will be searched for a valid system  partition.
  4. Allows redundant system partitions (IML).
  5. Sharing of SCSI devices.  An external SCSI device, such as the 3511,  may be shared between two system units.

  The following models are affected:
  1. Only the following processor boards with an EPROM module label having the following part    numbers may be upgraded:

PROCESSOR  FRU P/N   MODEL     EPROM P/N            LOC.
20MHZ SX   92F0049   0GX        91F9812             U36
25MHZ DX   64F0201   0JX       84F9154 OR 91F9812   U36
33MHZ DX   64F0198   0KX       84F9154 OR 91F9812   U36
50MHZ DX   92F0048   P3 (UPGD) 91F9812              U44
  It was called the "8590/95 Dual Booting Capability EPROM Package" 

 Type 1         PART NUMBER 52G9509 (was 52G9750 - try this if other PN is not known)

  NOTE:  Use the latest refdisk and diags. See above...


191-052 IBM PS/2 486/25 AND 486/33 PROCESSOR UPGRADE OPTIONS
190-186 IBM PERSONAL SYSTEM/2 486/33 PROCESSOR UPGRADE OPTION
"J" 486DX 25 MHz 64F0201 (old 84F8036)

OS1 25.0000 MHz Osc
OS2 20.0000 MHz Osc
U1 CPU
U7 57F2194 Memory Controller
U8 142 pin PGA socket for Weitek
U16, 20
78F1659 Memory Data Buffer
U16, 20 54F2958 Memory Data Buffer (old)
U19
17nS 256KB L2 cache daughtercard
U30 54F2958 MCA Buffer (old)
U30 78F1659 MCA Buffer
U36 BIOS (AM27C010)
U38 90X8134 DMA Controller

The J complex has been seen in three guises:
   142 pin socket for Weitek 4167
   Solder pads, but no socket SOD)
   No solder pads 

"K" 486DX 33 MHz 64F0198

OS1 33.0000 MHz Osc
OS2 20.0000 MHz Osc
U1 CPU
U7 57F2194 Memory Controller
U8 Space for 142 pin PGA socket

U16, 20 78F1659 Memory Data Buffer
U19 17nS 256KB L2 cache daughtercard
U30 78F1659 MCA Buffer
U36 BIOS (AM27C010)
U38 90X8134 DMA Controller

Solder pads in U8 are the mark of the SOD. If your complex doen't have them, it is not affected. Non-SOD complexes support a Turbochip. (well, usually. IBM made SO many different revisions...)

The K complex has been seen in two guises:
   Solder pads, but no socket SOD)
   No solder pads 

What is the SOD?
> What exactly is this square of death? (SOD)?
It is the mark of the beast. This square of solder pads is actually the binary equivalent of 666.

David Beem responds:
     The missing A1 & A2 pins make this a dead giveaway for the Weitek 4167. Steven Wachtel reports "memory management" problems (ECA #0530) with the SOD complex, which might make sense since the Weitek processors use high memory areas to transfer op codes. So, can a socket go in place to see if a 4167 would be functional there, or was it a dropped option? I suppose that with a couple SOD T1s (one of each of the patches talked about in this thread) & a Weitek 4167 I am one of those that could answer the question.

>Regarding the sensitivity of this complex, has anyone ever tried to swap the BIOS with another Type 1 complex that is known to work with the faster CPUs?

     Despite the complexi being very similiar & using the same reference disk, fundamental changes for things like the Weitek coprocessor could really mess things up. IBM would issue a whole complex if there was problems, not just a BIOS change. Other than the T4 'N' I have seen no 
evidence of other complex types checking things like CPUID.

Peter adds:
   The only reflection from the past is the comment of an IBM employee confronted with that exact question. He said "Forget about it".

   He then added that the complex had been designed at a time when IBM was yet "Big Blue" and tended not to give too much control over their products to one OEM and they therefore integrated provisions for a "non-Intel" MCU (the Weitek), but the full integration never came.

   Practically the SOD can be judged as an analog to the "spare" dual-in-line artifact solder spots that can be found on many cards, where the developers planned to build "something" but weren't sure what it could be and how it should look. Reserve spots in a way suitable for add-ons or patches, barely attached to the whole board - apart from power, GND and some basic adress / data / signal lines. The outline matches the Weitek math-co, but it is (after my knowledge) not supported from neither the glue logic nor the platform BIOS.

SOD Limitations from Tim Clarke
   The limitation of the 'poor DMA controller' for the Type-1 SOD board appears to be that you can't run a Cyrix/IBM 5x86 at greater that 'x2 clocking' (i.e. 50Mhz in a Type-2, 66Mhz in a Type-1) or an AMD 586 at greater than 'x3 clocking' (i.e. 75Mhz in a Type-2, 100Mhz in a Type-1). Ed. You CAN run a 486DX4-100 ODPR on a SOD. It's only a 3x multiplier.
   Not having a SOD Type-2 I can't test this, but I would expect the same limits to apply. So, you should be able to run a DX2-50, DX2-ODPR (@ 50Mhz), Cyrix/IBM 5x86 (@50Mhz) or AMD 586 (@ 75Mhz) in a SOD Type-2. The 'performance' of a Cyrix/IBM 5x86 @ 'x2 clocking' and the AMD 586 @ 'x3 clocking' are *roughly* equal, although I have a preference for the Cyrix/IBM chip.

ECA #0530 90-OK9/95-OKD with Complex P/N 84F9356

Steven Wachtel wrote:
   These systems appear to have a memory management problem.  In my environment it was seen on a Model 90 with 16 MB of RAM.  The system would hang during OS2 boot or during invocation of simple processes after a basic install (such as the system editor ).  Symptoms at other OS2 sites would  include excessive "random" trap errors.  Not using DOS on these systems, I  would expect the problem to surface as some indeterminate memory related failure in the E/XMS region.
    During initial setup of this machine, the problem appeared as an inability to create a useable backup reference disk ( if said disk was used there were always errors ).  On restart after the failure the machine will request to exec its own auto-reconfiguration and mark out the "bad" regions.  For my situation I had the IBM CE on-site for ~6 days for two separate events.  The CE changed each memory chip and riser (for the M90) multiple times and recombined them in every combinatorial representation. 
   Today (11/5/91) after following his instincts and direction of the higher level support reps, he contacted them again. They asked for the part number of the CPU board, upon which rests a Gate Array based custom memory controller.  He was advised that there are *known* problems with the down-rev boards in my new machines.  This problem exists(ed?) on the 0KD models of the M90 and M95, and possibly (as I do not have any to verify this ) the 0JD models.  IBM's second level support is apparently aware of this potential problem, but has not disseminated this to the CE level or the purchasing customer. 

Problem part identification and rectification:
   If the Processor Complex ( nee-CPU board ) part number is 84F9356 ( or 84F anything ? ) on the "barcode/label" of the board you should get a replacement. 
   The replacement part bears the part number 92F.....  I do not know if this is free.  Note, I have a M95 with this later board version that has never hown any of these problems.



Upgrade 486DX2-66  92F0145
192-178 IBM PS/2 486DX2-66 PROCESSOR UPGRADE OPTION

OS1 33.0000 MHz Osc
OS2 20.0000 MHz Osc
U1 CPU
U7 57F2194 Memory Controller
U8 space for 142 pin PGA socket
U16, 20 78F1659 Memory Data Buffer
U19 17nS 256KB L2 cache daughtercard
U30 78F1659 MCA Buffer
U36 ???
U38 90X8134 DMA Controller

J4- Once you toggle this jumper you will end up in a 0129 3000 error - "EEprom Jumper is in the wrong position" and no boot or such. I'd reported that some time ago while testing around with the 92F0145.
  Most likely it was originally intended to give the -0145 with 2 banks of EEprom to choose between - but by what reason they installed only one bank and the alternative setting branches into a BIOS error-code instead.

Peter sez:
   As a follow up notice: Yes - it *has* a flash-BIOS. And - Yes - it comes up with the Type-1 reference disk. Even installs a reference partition as usual with these disks.
   But the system permanently fails to boot into this Type 1 reference partition. Once you reboot it and press [ctrl]+[alt]+[ins] at CP 66 (cursor top / right) the machine loads the operating system instead jumping into reference.
   The platform nicely takes the Kingston Turbochip *without* restoration of the system partition. Runs fine with it - right from the start.

Supports Non-IML Configurations
  Dennis Smith found out that this complex can successfully boot without an IML device at ID6. He booted a SCSI drive at ID0 WITH NO IML track. I did it here with my upgrade DX2-66.
   His guess was this complex was designed to support RAID Arrays, and the early RAID controller, "Passplay" had no ability to boot from an array.



Upgrade 486DX 50 MHz  92F0048


OS1 55.0000 MHz Osc
OS2 20.0000 MHz Osc
U1 CPU
U7 57F2194 Memory Controller
U8 Solder pads for 142 pin PGA socket

U16, 20 78F1659 Memory Data Buffer
U19 17nS 256KB L2 cache daughtercard
U30 78F1659 MCA Buffer
U36 BIOS (AM27C010)
U38 90X8134 DMA Controller

Some observations-
The chipset appears the same as other Type 1s with the addition of decoding circuitry.

FCC ID- ANOIBM486A50
This uses the standard Type 1 EPROM, 27010 / 27C010

L2 Cache- 92F0050
NOTE: This complex needs the 15nS cache. The other Type 1 complexes use 17nS memory.

From Peter
   As far as I can tell (from the pictures of that complex) it varies through some different wiring and modified ASICs. The part of the hardware that deals with the CPU clock generation looks a bit different. The rest of the card is the "later" Non-SOD Type 1 platform as I have it here in my trusty old AKD.
   It seems as if IBM wanted to offer an upgrade path to DX-50 *without* the ECC option - for those customers that have a -xKx machine already and for the Mod. 90 maybe, which does not cope with the "2 layers" DX-50 Type 3 platform very well.
   This board was not offered with any particular Mod. 90 / 95 right from the start. It has been an option only. 


Specifications
Memory, Cache, Features
Min/Max on system board: 8/64MB 
RAM: DRAM (PS/2 72-pin SIMM) Interleaved (Install SIMMs in pairs) 70ns parity checked 
   Although 80 and 85 nanosecond (ns) memory Single In-Line Memory Modules (SIMMs) are supported, 70ns memory SIMMs provide optimum memory performance.
ROM: 128kb 
Cache: 8kb L1, optional 256kb L2 J and K complexes 
* Socket for optional L2 256K write-through memory cache on "J", "K", and  "Upgrade" DX2-66 (256 K write-thru standard with 486DX-50 ).
* No math coprocessor socket on "J", "K", and  "Upgrade"  complexes.
* 24 bit DMA; 10-12 MHz. (10-12? One or the other, please)
* Dual path memory design (Dual Bus Interleave).
* 20 MB per second data transfer support (for MCA bus)

9595 Main Page